PK Glazing

Guide · Homeowners · 4 min read · Updated 17 November 2026

Misted Double Glazing: Causes, Repair Options and Costs

Short answer

Misting between the panes means the sealed unit's edge seal has failed and moist air has got inside. It cannot be wiped away and rarely clears for good. The usual fix is to replace only the sealed unit, keeping the existing frame. A new unit typically costs £90–£250 depending on size and glass type, and takes under an hour to fit once it has been made.

Misted Double Glazing: Causes, Repair Options and Costs

Why double glazing mists up

A double glazed sealed unit is two panes of glass held apart by a spacer bar and bonded around the edge with a sealant. The spacer contains a desiccant that absorbs any moisture trapped during manufacture. Over time, sunlight, temperature swings and water sitting in the frame break down the edge seal. Once moist air gets in and the desiccant is saturated, condensation forms on the inside faces of the glass.

Misting usually appears first on cold mornings and clears later in the day, then gradually becomes permanent, leaving white streaks or a cloudy film. It is most common on south-facing windows that get strong sun, and in frames where blocked drainage slots let water sit around the bottom of the unit.

Misting inside the unit or on the room side?

Condensation on the room-side face of the glass is a different issue. It points to high humidity indoors from cooking, drying clothes or poor ventilation, and is cured by better ventilation, using trickle vents and extractor fans, rather than new glass. Condensation on the outside face on cool, clear mornings is a sign of a well-insulated modern unit and clears as the sun warms the glass.

To check, wipe both sides of the glass. If the moisture stays after wiping, it is between the panes and the unit needs replacing.

  • Room side: ventilation issue, not a faulty unit
  • Outside face: normal for efficient glazing, clears naturally
  • Between the panes: failed seal, replace the sealed unit

Your repair options

Replacing the sealed unit is the reliable fix. The repairer measures the existing glass size and thickness, notes the glass type and orders a new unit to suit. On the return visit the glazing beads are removed, the old unit lifted out, the new one packed and seated, and the beads refitted. Most frames take well under an hour each.

Some firms offer drilling and defogging, where small holes are drilled into the glass, the unit is cleaned and dried and the holes are plugged. This can improve appearance, but the seal remains failed and the insulating gas has gone, so thermal performance does not recover. We recommend replacement in almost every case.

OptionTypical costResult
Replace sealed unit only£90–£250 per unitAs-new glass performance, frame retained
Replace whole window£450–£900 (uPVC)New frame, glass and hardware
Drill and defogVariesCosmetic only, seal still failed

When to replace the whole window instead

If the frame is sound, a new sealed unit is almost always the better value. Consider full replacement if the frame is discoloured, warped or cracked, if hinges and locks have failed as well, if several units in the same window are misted, or if the frames are over 25 years old and other windows are going the same way. At that point, the cost of several new units plus hardware starts to approach a new window.

Full replacement also makes sense if you want a meaningful efficiency upgrade, since older frames may not take modern thicker units. A surveyor can tell you on one visit which windows are worth repairing and which are worth replacing.

How to prevent sealed units failing early

Sealed units do wear out eventually, but a few simple habits help them last longer. The most important is keeping the drainage slots at the bottom of the outer frame clear. These let rainwater that gets past the outer seals drain away. If they block with dirt, leaves or insects, water sits in the frame rebate around the bottom edge of the glass, where it attacks the edge seal. A quick clean with a soft brush or a cotton bud a couple of times a year makes a real difference.

Avoid using pressure washers directly on the edge of the glass and the gaskets, and avoid harsh solvents that can degrade sealants. Check that the glazing beads are sitting tight and that external gaskets are not shrinking or pulling away at the corners. On windows that get strong afternoon sun, failure tends to come sooner, so these are the ones to keep an eye on. When replacing units, choosing a good-quality unit with a warm-edge spacer and dual seal gives the best chance of a long service life.

  • Clear drainage slots twice a year
  • Do not pressure-wash the glass edges
  • Check gaskets and beads for shrinkage
  • Watch south and west-facing windows closely

Safety glass and specification

When a unit is replaced, the new glass should meet current rules for its location. Glazing in or beside doors, and low-level panes below 800mm from the floor, are critical locations that need toughened or laminated safety glass. Your repairer will check for a kitemark in the corner of the existing glass and specify safety glass where required, even if the original did not have it.

You can also upgrade the glass at the same time, for example to a low-emissivity coating with argon fill and a warm-edge spacer, obscure glass for a bathroom, or acoustic laminated glass for a bedroom facing traffic. The cost difference is usually modest when the unit is being made anyway.

Questions people also ask

Can misted double glazing fix itself?

No. Once the edge seal has failed, moisture keeps getting in and the desiccant cannot absorb it. Misting may come and go with the weather at first, but it gets worse over time and the only lasting fix is a new sealed unit.

Is misted double glazing a problem?

It is mainly a visual and comfort issue. The failed seal means the insulating gas has escaped, so the window loses some of its thermal performance. It is not dangerous, but it will not improve and the view will get worse.

How long does it take to replace a misted unit?

The repairer measures on the first visit, and units are typically made within one to two weeks. Fitting is then usually under an hour per window, with no need to remove the frame or disturb the plaster.

Written and checked by the PK Glazing team. Read our editorial policy.

Get a free double glazing quote

Tell us what you need and we'll come back with a clear price.

Request a quote